Differences

This shows you the differences between two versions of the page.

--- inventory:cnc_6040z [2017/10/29 16:49] – dp
+++ inventory:cnc_6040z [2019/11/11 09:56] (current) – dp
@@ Line 1: / Line 1: @@
 ====== CNC 6040Z ======
-===== TODO!!! =====
+===== port pinning =====
+<code>
+JP-3163B ver. 3.9
+Pin 1: Spindle on/off Relay 1(active low)
+Pin 2: X Axis Step (active low)
+Pin 3: X Axis Dir (active low)
+Pin 4: Y Axis Step (active low)
+Pin 5: Y Axis Dir (active low)
+Pin 6: Z Axis Step (active low)
+Pin 7: Z Axis Dir (active low)
+Pin 8: A Axis Step (active low)
+Pin 9: A Axis Dir (active low)
+Pin 10:Estop (active low)
+Pin 11: X Axis Limit Switch (active high) = when NC switch(es) open
+Pin 12: Y Axis Limit Switch (active high)
+Pin 13: Z Axis Limit Switch (active high)
+Pin 14: Buffer Chips “Enable” controlled by computer if Jumper 3 is set to 1-2 position
+Pin 15: Probe (active low)
+Pin 16: Is supposed to turn Relay 2 on/off but is currently not connected in board.
+Pin 17: PWM 0-10V for VFD Spindle AN1 (if jumper 4 is in default 1-2 position) active low
+Pin 18: Gnd
+Pin 19: Gnd
+Pin 20: Gnd
+Pin 21: Gnd
+Pin 22: Gnd
+Pin 23: Gnd
+Pin 24: Gnd
+Pin 25: Gnd or NC
+</code>
+===== sheme =====
+  * https://radiona.org/wiki/_media/inventory/6040z_psu_and_spindle_schematic_for_yoocnc_nt65-3x.pdf
+  * https://radiona.org/wiki/_media/inventory/6040z_yoocnc_nt65-3x_stepper_controller_schematic.pdf
+===== !!! TODO !!! =====
+==== DB25M kabel ====
+DB25M na DB25M ... kupiti
 ==== Stol ====
-Od profilnih cijevi sa kotačima (da ga je lakše selit i transportirat). Gore lim ili kada uz poklopce sistemom da se skine radi čiščenja i održavanja. U donji dio konstrukcije stola se strpaju police- nešto kao ormar za alat, plus rezervoar za vodu te sauger / ili mali kompresor.
+Mario: Od profilnih cijevi sa kotačima (da ga je lakše selit i transportirat). Gore lim ili kada uz poklopce sistemom da se skine radi čiščenja i održavanja. U donji dio konstrukcije stola se strpaju police- nešto kao ormar za alat, plus rezervoar za vodu te sauger / ili mali kompresor.
+Ivica: optimalne dimenzije cijevi za sto bile bi 30x30x1,5. Stol ne bi smio bit na kotacima dok stroj radi, treba stavit podesive nogice s navojem minimalno M12. vani treba ostavit oko 10mm navoja da se moze spustit na kotace.
 ==== Pleksi tacna i poklopac ====
@@ Line 40: / Line 81: @@
 ===== Software =====
-https://github.com/machinekit/machinekit
+  * EMC2 / LinuxCNC (str. 36+ iz [[http://radiona.org/wiki/_media/inventory/cnc-6040-router-engraver-system-installation-manual.pdf|manuala]])
+  * https://github.com/machinekit/machinekit
+  * Mach3
+  * neki kineski demo šit koji dođe s njim
 ----
@@ Line 93: / Line 137: @@
 ===== User manuals =====
+  * [[http://radiona.org/wiki/_media/inventory/cnc-6040-router-engraver-system-installation-manual.pdf|CNC-6040-Router-Engraver-System-Installation-Manual.pdf]]
+  * [[http://radiona.org/wiki/_media/inventory/cnc_6040_cnc_6040z_s65j_user_manual.pdf|CNC_6040_CNC_6040Z_S65J_User_Manual.pdf]]

User Tools

Site Tools

Differences

Page Tools