Differences

This shows you the differences between two versions of the page.

--- inventory:cnc_6040z [2017/10/29 09:02] – dp
+++ inventory:cnc_6040z [2019/11/11 09:56] (current) – dp
@@ Line 1: / Line 1: @@
 ====== CNC 6040Z ======
-==== Tehničke karateristike ====
+===== port pinning =====
+<code>
+JP-3163B ver. 3.9
+Pin 1: Spindle on/off Relay 1(active low)
+Pin 2: X Axis Step (active low)
+Pin 3: X Axis Dir (active low)
+Pin 4: Y Axis Step (active low)
+Pin 5: Y Axis Dir (active low)
+Pin 6: Z Axis Step (active low)
+Pin 7: Z Axis Dir (active low)
+Pin 8: A Axis Step (active low)
+Pin 9: A Axis Dir (active low)
+Pin 10:Estop (active low)
+Pin 11: X Axis Limit Switch (active high) = when NC switch(es) open
+Pin 12: Y Axis Limit Switch (active high)
+Pin 13: Z Axis Limit Switch (active high)
+Pin 14: Buffer Chips “Enable” controlled by computer if Jumper 3 is set to 1-2 position
+Pin 15: Probe (active low)
+Pin 16: Is supposed to turn Relay 2 on/off but is currently not connected in board.
+Pin 17: PWM 0-10V for VFD Spindle AN1 (if jumper 4 is in default 1-2 position) active low
+Pin 18: Gnd
+Pin 19: Gnd
+Pin 20: Gnd
+Pin 21: Gnd
+Pin 22: Gnd
+Pin 23: Gnd
+Pin 24: Gnd
+Pin 25: Gnd or NC
+</code>
+===== sheme =====
+  * https://radiona.org/wiki/_media/inventory/6040z_psu_and_spindle_schematic_for_yoocnc_nt65-3x.pdf
+  * https://radiona.org/wiki/_media/inventory/6040z_yoocnc_nt65-3x_stepper_controller_schematic.pdf
+===== !!! TODO !!! =====
+==== DB25M kabel ====
+DB25M na DB25M ... kupiti
+==== Stol ====
+Mario: Od profilnih cijevi sa kotačima (da ga je lakše selit i transportirat). Gore lim ili kada uz poklopce sistemom da se skine radi čiščenja i održavanja. U donji dio konstrukcije stola se strpaju police- nešto kao ormar za alat, plus rezervoar za vodu te sauger / ili mali kompresor.
+Ivica: optimalne dimenzije cijevi za sto bile bi 30x30x1,5. Stol ne bi smio bit na kotacima dok stroj radi, treba stavit podesive nogice s navojem minimalno M12. vani treba ostavit oko 10mm navoja da se moze spustit na kotace.
+==== Pleksi tacna i poklopac ====
+  * Plexi ili kupovna tacna visine 5-10 cm ivodonepropousna. U tacnu treba stat cijeli CNC i ostat 5 cm sa svake strane
+  * Plexi poklopac koji uđe unutar tacne (da špena i špricanje ostane u tacni
+  * Sigurnosni prekidač - ako se digne poklopac da mašina stane (hall sensor na tacni i magnetić na poklopcu npr)
+  * https://www.thingiverse.com/thing:2246287 ???
+==== End-stopovi ====
+end-stop senzori sa svake strane, 6 komada
+  * https://www.thingiverse.com/thing:30253 možda ovo
+==== Komp ====
+linux kompjuter za wifi -> linuxcnc/gcode -> SXCNC pošalje mu se fajl za samostalno glodanje. Može
+  * PC (micro atx, nuc-alike fanless sa PCI-LPT karticom,
+  * Stari_laptop (njuškalo, krama) sa LPT portom
+  * RPI3 ako mu napravimo gpio -> lpt flat cabl adapter)
+==== Set alata za stezanje ====
+Opremu za stezanje obradaka odmah naručit. Dobar škripac (pazit da nije previsok) i set za stezanje (tipa ovo:
+  * http://www.alco.co.rs/index.php/pribor/stege-i-radni-stolovi/setovi-za-stezanje-i-vezivanje/set-za-stezanje-58-elemenata)...
+  * https://www.thingiverse.com/thing:222531 ili ovako nešto 3d printano
+==== Set alata ostalo ====
+set alata za glodanje potrošnih raznih veličina (ebay)
+==== Bulk materijal ====
+Bulk kvalitetnog aluminija za glodanje npr AlS1Mn 5 mm, 1 m^2
+==== Puhalica zraka i tekućine ====
+  * https://pt.aliexpress.com/af/CNC-Machine-Round-Nozzle-Plastic-Flexible.html?SearchText=CNC+Machine+Round+Nozzle+Plastic+Flexible&ltype=wholesale&d=y&tc=main&blanktest=0&origin=n&catId=0&isViewCP=y
+  * ili usisavač https://www.thingiverse.com/thing:1953916
+----
+===== Software =====
+  * EMC2 / LinuxCNC (str. 36+ iz [[http://radiona.org/wiki/_media/inventory/cnc-6040-router-engraver-system-installation-manual.pdf|manuala]])
+  * https://github.com/machinekit/machinekit
+  * Mach3
+  * neki kineski demo šit koji dođe s njim
+----
+===== Tehničke karateristike =====
 == 6040 triaxial engraving machine part parameters: ==
@@ Line 41: / Line 128: @@
   * Protection:Emergency stop button
+===== Control box iznutra =====
-==== Kupiti ====
-Opremu za stezanje obradaka odmah narućit. Dobar škripac(pazit da nije previsok) i set za stezanje(tipa ovo: http://www.alco.co.rs/index.php/pribor/stege-i-radni-stolovi/setovi-za-stezanje-i-vezivanje/set-za-stezanje-58-elemenata)...
-==== Control box iznutra ====
 {{:inventory:cnc_6040z_control_01.jpg?direct&100x100|}}
 {{:inventory:cnc_6040z_control_02.jpg?direct&100x100|}}
@@ Line 53: / Line 136: @@
 {{:inventory:cnc_6040z_control_06.jpg?direct&100x100|}}
+===== User manuals =====
+  * [[http://radiona.org/wiki/_media/inventory/cnc-6040-router-engraver-system-installation-manual.pdf|CNC-6040-Router-Engraver-System-Installation-Manual.pdf]]
+  * [[http://radiona.org/wiki/_media/inventory/cnc_6040_cnc_6040z_s65j_user_manual.pdf|CNC_6040_CNC_6040Z_S65J_User_Manual.pdf]]

User Tools

Site Tools

Differences

Page Tools